Dishwasher Drain Solenoid Kit with Bracket (GE OEM)

Description

Genuine GE OEM Dishwasher Drain Solenoid Kit with Bracket – Part WD21X10060

Part Number: WD21X10060

Replaces: AP2039738, PS260117, WD21X10057, WD21X10064, DW10060, 271344

Always verify compatibility using your appliance model number before ordering.

GE Dishwasher Drain Solenoid Kit and Bracket (Part # WD21X10060)

Restore reliable drainage control and quiet cycle transitions to your laundry and kitchen cleanup routines with this Genuine OEM GE Dishwasher Drain Solenoid Kit and Bracket. Designed specifically for classic mechanical-valve GE and Hotpoint dishwasher drain mechanisms, this heavy-duty electromagnetic assembly mechanically actuates the drain valve flapper to release dirty water from the tub.

Mounted directly to the lower pump assembly under the tub frame, this complete kit includes the solenoid coil, plunger linkage, mounting bracket, return spring, and essential installation hardware. When energized by the timer or control board during a drain sequence, the electrical coil draws the plunger down, actuating the drain valve lever to divert pump pressure out through the drain hose rather than through the wash spray arms.

If this part fails, the coil can short out or overheat, the return spring can break, or the mechanical linkage can bind. This leads to frustrating failure symptoms, including a dishwasher that refuses to drain water at the end of a cycle, persistent burning smell during operation, loud buzzing or clicking under the tub without water evacuating, or water remaining trapped in the bottom basin.

Quick Info

• Compatibility: Precision-engineered for classic General Electric, Hotpoint, and RCA built-in dishwashers utilizing solenoid-actuated drain valves.

• Advanced Features: Complete factory repair kit with 120V electromagnetic solenoid coil, heavy-duty mounting bracket, actuator lever linkage, tension spring, and mounting clips.

• Fixes Common Issues: Resolves standing water in the bottom tub; failure to actuate drain valve; loud solenoid buzzing, burning, or clicking noises; and bound or broken mechanical drain linkages.

• Difficulty: Intermediate. A direct DIY installation requiring a nut driver, screwdriver, pair of needle-nose pliers, and roughly 30 to 45 minutes.

💡 Critical Diagnosis & Prevention Tip

If your solenoid coil looks scorched, discolored, or smells burnt, do not just replace the solenoid without checking the actuator arm!

A jammed or binding drain valve linkage forces the solenoid coil to stay under high continuous electrical load, causing the coil to overheat and burn out within minutes. Before securing your new WD21X10060 kit, manually actuate the drain valve arm by hand. It should move freely and snap back smoothly under spring tension. If it binds, clean any food debris or mineral buildup around the pivot shaft!

Step-by-Step Replacement Guidelines

1. Utility Isolation: Completely disconnect power to the dishwasher at your home’s main electrical breaker panel, and turn off the hot water shutoff valve under the kitchen sink.

2. Expose the Lower Pump Mechanism: Unthread and remove the screws securing the lower front access kickplate panel. Lay down a towel underneath to catch any stray drops of water.

3. Remove the Failed Solenoid Assembly: Locate the drain solenoid on the lower pump assembly. Unplug the two spade wire terminals from the coil. Unhook the return spring, remove the retaining clip on the actuator arm linkage, and unbolt the mounting bracket screws to lift the failed solenoid free.

4. Assemble and Position the New Kit: Align the new OEM solenoid coil and bracket hardware. Connect the plunger linkage to the drain valve actuator lever and reinstall the retaining clip. Anchor the bracket to the pump frame with the mounting screws.

5. Rehook Spring & Wire Terminals: Attach the new tension return spring between the actuator lever and the bracket tab. Slide the electrical spade terminals securely onto the new coil terminals, restore power and water, and run a short wash-to-drain cycle to verify crisp valve actuation and full drainage.