Dryer Lint Filter Guide Cover (LG OEM)

Description

Genuine LG OEM Dryer Lint Filter Guide Cover – Part 3550EL1005C

One of three pieces in the lint filter assembly. ~16 inches wide plastic. Also compatible with Kenmore.

Part Number: 3550EL1005C

Replaces: AP6302068, 3550EL1005B, 3550EL1005A, 4869226, PS12368455

Always verify compatibility using your appliance model number before ordering.

LG Dryer Lint Filter Grille & Guide (Part # 3550EL1005C)

Restore a perfectly flush, snag-free surface to your dryer’s door opening with this Genuine OEM LG Dryer Lint Filter Grille. This factory-certified replacement cover plate (Part # 3550EL1005C, which directly replaces older part numbers like 1266856, AH3522989, and EA3522989) functions as the primary protective shield and guide channel for your appliance’s air exhaust system.

Screwed directly into the lower front bulkhead housing inside the door opening, this grid-patterned cover acts as a structural seat that holds your removable mesh lint filter securely upright in its tracking groove. The open grate design allows high-velocity, moisture-laden air to be drawn cleanly out of the tumbling drum while physically preventing small laundry items—like baby socks, loose buttons, handkerchiefs, or underwire—from slipping down into the internal blower wheel housing and seizing the motor.

If this grille is cracked, warped from high heat, or lifting away from the bulkhead panel, it creates a jagged edge that will constantly catch, snag, and tear your clothing during a drying cycle.

Quick Info:

• Compatibility: Precision-engineered exclusively for LG and Kenmore Elite (796-Series) front-loading gas and electric dryers.

• Structural Design: Contoured, high-strength plastic crescent grate designed to match the exact curvature of the lower drum entry rim.

• Fixes Common Issues: Resolves clothing snagging, tearing, or twisting around the lint trap; a loose or wobbling main lint filter; and physical cracking of the lower door trim layout.

• Difficulty: Novice. A very straightforward DIY repair typically requiring only a single Phillips screwdriver and less than 10 minutes.

Pro Tip: If your clothes are constantly getting ruined by getting wrapped around or caught on the corner of the lint screen area, a cracked grille plate is usually the smoking gun. However, when you unbolt the old plate, pay close attention to the underlying metal bulkhead alignment. Over time, slamming the heavy dryer door or leaning heavily on the open door frame can slightly warp the front sheet metal panel. When you fit the new genuine grille cover, ensure it sits completely flush against the surrounding frame. If there is even a millimeter gap left exposed, thin fabrics like bedsheets and t-shirt straps can still slide into the crack mid-cycle, twisting tightly until the friction burns or rips the fabric.

Installation & Safety Steps:

1. Isolate Power: For complete mechanical safety, unplug the dryer’s power cord from the wall or switch off the house circuit breaker before working inside the drum frame.

2. Remove the Main Filter: Open the dryer door completely and pull the removable mesh lint screen assembly straight up and out of the slot.

3. Unbolt the Broken Grille: Locate the Phillips screws anchoring the crescent-shaped plastic grille to the front metal bulkhead structure. Unthread the screws carefully so they do not drop down into the open exhaust chute below.

4. Clean the Chute: With the grille completely removed, take a flashlight and peer down into the exposed exhaust pocket. Use a vacuum crevice tool to pull out any compressed lint balls, loose coins, or stray buttons that have slipped past the trap before installing the new plate.

5. Mount the Replacement: Position the new genuine factory grille over the alignment pins on the housing rim. Hand-tighten the mounting screws securely, ensuring the plastic doesn’t crack from over-torqueing. Slide your mesh lint filter back into its track to verify it seats fully flat.

Are you replacing this grille cover today because it cracked and started snagging your clothes, or did a small object fall down inside the exhaust housing and break the inner plastic tracks?