Dryer Power Cord 5 ft 30-Amp 3-Wire (GE OEM)

Description

Genuine GE OEM Dryer Power Cord 5 ft 30-Amp 3-Wire – Part WX09X10003

Part Number: WX09X10003

Replaces: AP2044850, PS232427

Always verify compatibility using your appliance model number before ordering.

GE 5-Foot 3-Wire Clothes Dryer Power Cord (Part # WX09X10003)

Safely supply high-voltage electrical energy to your laundry appliance with this Genuine OEM GE 3-Wire Clothes Dryer Power Cord. This factory-certified, heavy-duty power line (Part # WX09X10003) provides an extra foot of reach compared to standard 4-foot cords, giving you more installation flexibility if your wall outlet is spaced further away from the appliance. It is engineered to comfortably manage the substantial electrical current required to run an electric dryer’s 5400-watt heating element and drive motor simultaneously.

Constructed with thick-gauge copper conductors wrapped in a rugged, heat-resistant PVC insulating jacket, this 5-foot cord features molded heavy-duty ring terminals at the connection ends to guarantee a stable, arc-free interface with your machine’s rear electrical block.

If your current cord feels hot to the touch, has melted or scorched plug prongs, shows exposed wiring insulation, or was cut during a household move, replacing it immediately eliminates catastrophic electrical and fire hazards.

Quick Info:

• Compatibility: Universally compatible with GE (General Electric), Hotpoint, Haier, Monogram, Café, Whirlpool, Maytag, Kenmore, Amana, Frigidaire, and LG electric clothes dryers requiring a 3-prong hookup.

• Electrical Specifications: Rated for 30 Amps at 125/250 Volts. Features a classic NEMA 10-30P angled plug design to sit flush against your laundry room wall.

• Physical Layout: 3-Wire Configuration consisting of two hot lines (carrying 120V each to total 240V across the element) and one shared neutral/ground wire line.

• Difficulty: Novice. A very straightforward installation requiring only a nut driver or Phillips screwdriver to access the rear connection block panel.

⚠️ Critical Code & Safety Warning:

National Electrical Code (NEC) regulations regarding appliance grounding changed in 1996.

• 3-Wire Cords (Like This One): Are typically legal only if your home was built before 1996 and features an older 3-slot wall outlet.

• 4-Wire Cords: If your home was built after 1996, or if your laundry room was updated recently, you will have a modern 4-slot wall outlet. You cannot plug a 3-wire cord into a 4-slot outlet. Make sure to check your wall receptacle before buying to ensure you aren’t installing the wrong wiring configuration!

Step-by-Step Installation Guidelines:

    [ BACK OF ELECTRIC DRYER ]
    
       Terminal Block Studs
        (L1)    (N)    (L2)
         |       |       |
         v       v       v
       [Red]  [White] [Black]
         \       |       /
          \      |      /
           ======#======  <-- Strain Relief Clamp
                 ||
                 ||  <-- Power Cord

1. Absolute Power Isolation: Never attempt to wire a power cord while it is plugged into the wall. Ensure the cord is completely disconnected from any live power source, and shut off the dryer’s dedicated dual-pole circuit breaker at your main panel for added safety.

2. Remove the Access Plate: Locate the small metal terminal block inspection shield on the upper rear section of the dryer cabinet frame. Unthread the retaining screw and lift the shield off to expose the three brass terminal studs.

3. Install the Strain Relief: Slide the top half of the included metallic strain relief clamp into the circular cabinet knockout hole. This clamp prevents the metal edges of the cabinet from chafing through the rubber wire insulation over time.

4. Wire the Terminal Block (3-Wire Setup): Feed the ring terminals through the knockout. Connect the wires to the matching brass studs using a nut driver:

   • Outer Left Stud (L1): Attach the left hot wire (typically insulated in black or bare brass).

   • Center Stud (Neutral): Attach the center wire (insulated in white or light grey) alongside the dryer’s internal white neutral wire and its metal grounding strap. Securely bond the ground strap to the center terminal or adjacent green ground screw according to the manual diagram.

   • Outer Right Stud (L2): Attach the right hot wire (typically insulated in red or bare brass).

5. Secure and Close: Tighten the terminal nuts firmly to prevent loose connections, which cause high-resistance arcing and melt the block. Tighten the strain relief clamp screws down onto the cord jacket, and screw the rear metal access plate back into place.

Are you installing this 5-foot cord today because your wall outlet sits a little further away from your dryer layout, or are you replacing a shorter cord that has been damaged?