Front-Load Washer Door Lock Assembly (Older Platform) (LG OEM)

Description

Genuine LG OEM Front-Load Washer Door Lock Assembly (Older Platform) – Part EBF49827801

If the washer door is closed/locked. Fixes DE error code, door-will-not-start. Located behind the front panel; remove the gasket to access.

Part Number: EBF49827801

Replaces: AP4998848, 6601ER1004C, 6601ER1004B, 6601ER1004E, 1268254, EBF49827802, PS3533609

Always verify compatibility using your appliance model number before ordering.

LG Front-Load Washer Door Lock and Switch Assembly (Part # EBF49827801)

Restore smooth operation and structural safety to your laundry cycle with this Genuine OEM LG Washer Door Lock and Switch Assembly. This factory-certified safety component (Part # EBF49827801, which officially updates and replaces older variant configurations like 1341094, AP4441525, and PS3528800) acts as the primary electrical gatekeeper for your washing machine.

Front-load washers spin at incredibly high velocities, reaching up to 1200 RPM. To protect against accidental flooding or physical injury, this assembly combines a sensitive mechanical micro-switch with an internal electronic wax solenoid plunger. When you press start, the machine confirms the door latch hook is fully seated, then passes voltage to the solenoid to physically lock the door deadbolt. The switch then sends a structural verification signal back to the main control board, granting permission for the tub to safely fill and spin.

If this module suffers a mechanical breakdown or a water leak shorts out its delicate copper contacts, your washer will instantly halt operations. This causes critical failure symptoms, including a washing machine that flashes error codes (such as “dE”, “dE1”, or “dE2”), an electronic door latch that refuses to click or lock when a cycle is chosen, or a machine that finishes its wash cycle but traps your wet clothes permanently inside by refusing to unlock.

Quick Info:

• Compatibility: Precision-engineered exclusively for LG and Kenmore Elite (796-Series) front-loading high-efficiency (HE) washing machines.

• Component Housing: Heavy-duty thermoplastic protective casing equipped with integrated dual mounting screw eyelets, a molded catch funnel for the door strike hook, and a multi-pin wire harness plug seat.

• Fixes Common Issues: Resolves “dE” or “dE1” door lock error codes, a washer that refuses to start or initiate a high-speed spin cycle, a door latch that stays unlocked, or a door mechanism that gets stuck in a permanent lock-out loop.

• Difficulty: Novice to Intermediate. A highly accessible DIY repair requiring only a cross-tip screwdriver and a pair of needle-nose pliers—no full cabinet teardown necessary!

⚠️ Pro Shortcut Repair Strategy (No Panel Removal Needed):

Many internet repair guides will tell you that you must dismantle the entire front sheet-metal wall of your washer just to replace this switch. You don’t have to do that! You can easily complete this entire swap in under 10 minutes right through the front door opening:

1. Use a thin flathead screwdriver to pop off the outer thin wire spring clamp wrapping around the rubber door boot gasket, and peel just the right side of the rubber boot off the metal cabinet lip.

2. Fold the flexible rubber gasket back into the drum barrel. This creates a wide, comfortable hand gap right next to the door latch opening.

3. Reach your hand directly behind the metal panel skin, unbolt the two front phillips screws holding the lock assembly, pull the module forward out through the hand gap, swap the wiring harness, and slide it back into position!

Step-by-Step Replacement Guidelines:

1. Absolute Power Isolation: You must completely unplug the washing machine’s electrical power cord from the wall outlet or flip your home’s main circuit breaker switch to eliminate all high-voltage hazards before touching internal wire grids.

2. Remove the Outer Retention Ring: Open the washer door completely. Find the small tension spring located along the bottom edge of the outer thin metal wire loop holding the rubber door bellows to the front panel skin. Hook a small tool or needle-nose pliers into the spring coil loop, stretch it outward, and slide the wire ring completely away.

3. Peel the Gasket Back: Pull the right-hand edge of the gray rubber gasket boot off the circular metal lip of the cabinet door opening and fold it inward to clear a pathway for your hand.

4. Unbolt the Switch Module: Unthread the two vertical Phillips head mounting screws located on the outside face of the front cabinet wall, right next to the square catch hole where the door hook enters.

5. Swap the Wiring Loom: Reach your hand behind the metal front panel skin through the open rubber bellows gap and pull the lock switch module out. Depress the locking clip tab on the plastic multi-pin wiring harness plug and pull it straight away from the old switch. Snap the plug firmly into your fresh new genuine factory replacement module until it clicks, line the switch back up behind the cabinet screw slots, anchor it tightly, and wrap your rubber boot securely back over the outer panel frame rim.

Are you replacing this door lock switch assembly today because your washing machine is completely locked up and flashing a “dE” error code, or did the internal lock mechanically snap off?